LevelMatePRO FAQ and troubleshooting

Retail LevelMatePRO Troubleshooting

I can't connect to my LevelMatePRO
1. Ensure that you don’t have the app running on another phone or tablet. As is the case with all Bluetooth devices, the LevelMatePRO can only be connected to one tablet or phone at a time.
2. Ensure that you have a fresh battery installed in the LevelMatePRO and that the battery is installed properly. Note that the side of the battery with the ‘+’ on it should be facing up after the battery is installed. With the battery installed, switch the unit on and confirm that you hear a double beep. Launch the app again to see if a connection can be made.
3. If no connection is made, delete the LevelMatePRO app from all of your smartphones and/or tablets.
4. Power down your smartphones and/or tablets and then power them back up.
5. Download and install the LevelMatePRO app to all of your smartphones and/or tablets.
6. Switch the LevelMatePRO off and then on again.
7. Start the app on one of your smartphones or tablets. The LevelMatePRO should automatically link to your phone or tablet and a connection should be made.
If no connection is made, please email us at support@levelmate.co.nz
After my vehicle has been sitting for a long time, I cannot connect to my LevelMatePRO
LevelMatePRO was designed to be very power efficient and goes into a low power “sleep” mode after no motion is detected for a period of time (as configured in the app). Motion will wake the unit from low power mode. So if you can’t connect to your LevelMatePRO after it has been sitting for longer than the number of hours you configured in the app, there are a multiple ways to wake the system:

1. If Gen 2, switch the On/Off switch to the Off position and then back to the On position.
2. Create motion in the vehicle by driving it or by raising or lowering the jack.
3. Remove the LevelMatePRO cover and uninstall then reinstall the battery.
4. Pass a magnet over the cover of the LevelMatePRO.

I cannot link my LevelMatePRO to a second phone/tablet
First, ensure that you don’t still have the app running on the phone that is already linked. The LevelMatePRO can only connect to one tablet or phone at a time, and this limitation also applies to the “learning” period in which you attempt to link to a new device. Next, make sure you attempt to link to your LevelMatePRO within the 10 minute “learning” period that enables linking to occur. Once you have turned on your LevelMatePRO (by removing and reinserting a battery, or waking the unit, or if Gen 2, by switching the unit on), you will have 10 minutes to link with all of the phones or tablets that you plan to use with the product. If the 10 minute “learning” session has expired, simply remove and reinsert the battery (or if Gen 2, switch the unit off then on again) to start another 10 minute “learning” session.
I get inconsistent readings from my LevelMatePRO
If your LevelMatePRO app displays incorrect leveling information, the problem may be caused by an installation issue. Please consider the following when troubleshooting this problem:

1. The LevelMatePRO must be installed on a hard surface. If attached to carpet or insulation, for example, the unit will move too much and won’t operate properly.
2. The LevelMatePRO must be firmly attached to the mounting surface with screws. If attached using Velcro or double-sided tape, the unit will move too much and won’t operate properly.
3. The LevelMatePRO must not be installed near your power inverter, circuit breaker, or batteries.

Another reason you may see inconsistent readings is that your initial level position data did not get saved correctly. To ensure that this information is correctly stored on the unit, repeat the process of leveling your vehicle, then press the Set Level button in the app.

If your installation location is correct and you have resaved your Set Level data, but you are still getting inconsistent readings, please email us at support@levelmate.co.nz

OEM LevelMatePRO Troubleshooting

I can't connect to my LevelMatePRO

1. Ensure that 12v DC power is currently supplied to the RV. If your vehicle has been sitting for an extended period of time, your 12 volt batteries may need to be recharged.
2. Ensure that you don’t have the app running on another phone or tablet. As is the case with all Bluetooth devices, the LevelMatePRO can only be connected to one tablet or phone at a time.
3. Launch the app again to see if a connection can be made.
4. If no connection is made, delete the LevelMatePRO app from all of your smartphones and/or tablets.
5. Power down your smartphones and/or tablets and then power them back up.
6. Download and install the LevelMatePRO app to all of your smartphones and/or tablets.
7. Because you reinstalled the app, you will need to relink the LevelMatePRO with your phone or tablet. Put the LevelMatePRO in “learn” mode by pressing and holding the button on the front of the LevelMatePRO until you hear a long beep (approximately 3 seconds).
8. Start the app on one of your smartphones or tablets. The LevelMatePRO should automatically link to your phone or tablet and a connection should be made.

If no connection is made, please email us at support@levelmate.co.nz

After my vehicle has been sitting for a long time, I cannot connect to my LevelMatePRO
Ensure that 12v DC power is currently supplied to the RV. If your vehicle has been sitting for an extended period of time, your 12v batteries may need to be recharged.
I cannot link my LevelMatePRO to a second phone/tablet
First, ensure that you don’t still have the app running on the phone that is already linked. The LevelMatePRO can only connect to one tablet or phone at a time, and this limitation also applies to the “learning” period in which you attempt to link to a new device. Next, make sure you attempt to link to your LevelMatePRO within the 10 minute “learning” period that enables linking to occur. To put the LevelMatePRO in “learn” mode, press and hold the button on the front of the LevelMatePRO until you hear a long beep (approximately 3 seconds).

NOTE: You will have 10 minutes from the time you put the LevelMatePRO in “learn” mode to allow new smartphones or tablets to “learn” your LevelMatePRO. If this time expires, you can restart the 10 minute “learn” window using the same method described above to put the LevelMatePRO in “learn” mode.

I get inconsistent readings from my LevelMatePRO
If your LevelMatePRO app displays incorrect leveling information, the problem may be that your initial level position data did not get saved correctly. To ensure that this information is correctly stored on the unit, repeat the process of leveling your vehicle, then press the Set Level button in the app.
If you have resaved your Set Level data, but you are still getting inconsistent readings, please email us at support@levelmate.co.nz